CollectorBoard - Revision history

Krdarrah at 04:28, 9 November 2017

2017-11-09T04:28:26Z

2017-11-09T04:23:56Z

2017-11-09T04:19:51Z

2017-11-02T04:13:33Z

‎Parts

2017-11-02T04:06:18Z

‎Parts

2017-11-02T04:04:03Z

2017-11-02T04:03:37Z

2017-11-02T04:03:15Z

2017-11-02T04:01:07Z

2017-10-17T15:59:52Z

← Older revision		Revision as of 04:28, 9 November 2017
Line 56:		Line 56:

	Coming soon, but if you want to start testing, [http://www.kevindarrah.com/wp-content/uploads/2017/11/Collector_10_28__7.zip HERE] is some sample code that exercises all of the functionality on the board. Note that you'll need to download several libraries in order to successfully compile.		Coming soon, but if you want to start testing, [http://www.kevindarrah.com/wp-content/uploads/2017/11/Collector_10_28__7.zip HERE] is some sample code that exercises all of the functionality on the board. Note that you'll need to download several libraries in order to successfully compile.
		+
		+	For the microphone circuit tuning, it is a lot easier to do this using an oscilloscope, but to test it out:
		+	Rotate the "Mic Sensor" potentiometer fully clockwise and the "MIC Thresh" pot fully counter clockwise, then one quarter turn clockwise. Those are the settings I'm currently testing with.

← Older revision		Revision as of 04:23, 9 November 2017
Line 54:		Line 54:

	== Tutorials ==		== Tutorials ==
		+
		+	Coming soon, but if you want to start testing, [http://www.kevindarrah.com/wp-content/uploads/2017/11/Collector_10_28__7.zip HERE] is some sample code that exercises all of the functionality on the board. Note that you'll need to download several libraries in order to successfully compile.

@@ Line 31: / Line 31: @@
 * The OLED Display that has been tested with the board is the 0.96" 128x64 and uses Arduino Libraries for the SSD1306 driver using I2C.  The display tested was purchased [https://www.amazon.com/gp/product/B00O2KDQBE/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1 HERE].
-* The Motion Sensor pinout seems to vary, so make sure it is VCC-OUT-GND and that it supports a Vin of 3.3V.  Will update this section with a part number once that is tested.
+* The Motion Sensor pinout seems to vary, so make sure it is VCC-OUT-GND.  It turns out a lot of these modules only support a 5V input, so I modified the one I had to work with 3.3V.
 == Assembly ==
 == Tutorials ==

@@ Line 26: / Line 26: @@
 Parts List can be downloaded [http://www.kevindarrah.com/wp-content/uploads/2017/11/CollectorV1.xlsx HERE]
 == Assembly ==
 == Tutorials ==

@@ Line 24: / Line 24: @@
 == Parts ==
 == Assembly ==
 == Tutorials ==

@@ Line 18: / Line 18: @@
 == Schematic ==
-[[File:CollectorV1SCH.png|800px]]
+[[File:CollectorV1SCH.png|1000px]]
 == Purchase ==

← Older revision		Revision as of 04:01, 2 November 2017
Line 15:		Line 15:
	* Buzzer		* Buzzer
	* Silence Button - in case you want to mute all activity on the board.		* Silence Button - in case you want to mute all activity on the board.
		+
		+	== Schematic ==
		+
		+	== Purchase ==
		+	given to [https://www.patreon.com/kdarrah Patrons]
		+
		+	== Parts ==
		+
		+	== Assembly ==
		+
		+	== Tutorials ==

@@ Line 3: / Line 3: @@
 [[File:CollectorGerb.png|600px]]
-The Pusher Board is an IoT project that does one thing - it pushes you a notification triggered by a digital input.  Well, it's much more than that, but this is the inspiration.  I wanted to design a WiFi board that essentially sleeps most of its life, but when that door switch, flood sensor, motion sensor, etc.. gets triggered, I just want a notification immediately on my phone.  And that's about it... a perfect IoT device in the background doing its job.
+The Collector board was originally designed to work with the [[Pusher]] - basically a board that can "Listen" for push notifications.  This is especially useful for situations when notifications are disabled on the smart phone (Do Not Disturb mode at night).  In addition to receiving push notifications, it also interfaces to sensors that benefit from an 'always on' power source, such as Smoke Alarm detection, motion sensors, etc...  The board is based on the ESP8266 WiFi module, so it can also be used as a development board for other projects.
 = Version 1 =
+* All through-hole components except ESP-12S WiFi Module
-Very first prototype board
+* USB B or Barrel Jack for 5VDC power input with Power Switch
-* Mostly through hole com
+* Microphone Circuit to detect smoke alarms (made a [https://youtu.be/kLI6XKcR6PY video] on this recently)